Home > WATERWAY SPA PUMPS > Waterway Executive Pumps > Executive Pumps 3.1" Threads >

37212211D Blemished Waterway Executive Spa Pump 2-spd 230V 10.0/3.4A Executive 56f 6.5" diameter motor 2" SD/CS 3721221-1D 3.1" threads in/out
Waterway Spa Pump, 3721221-1D, 37212211d P230E52024 PF-30-2N22C, PF302N22C, 285.30,  Massage Master XLT, PF-25-2N22C, PF-20-2N22M, PF-30-2N22M, 3721221-0D5A, PF-30-2N22C, 3721221-0D87


 
Alternative Views:


Price: $459.50


Availability:: not available
Product Code: 37212211DBLEM

Description
 
Blemished. See second photo please showing only 1 screw holding the dust cover in place at the rear

of the motor. The area the screw attaches to was stripped and broken off. One screw is plenty good enough to

hold this small cover in place. The cover and 1 screw is what you'll receive with this fully tested pump and motor.

Discounted due to the blemish.

3721221-1D Waterway Executive Spa Pump 2-speed, 230V, 10.0/3.4A 3hp Executive 56 frame 3hp 6.5" diameter Threaded connections are both 3.1" outside diameter (meant for 2" pvc pipe size) 2" SD/CS. High performance Water Way Hot Tub Pump, very strong A.O. Smith motor, split capacitor design, double shielded ball bearings. Viton Seals, has 3.1" outside diameter threads on inlet and outlet. Massage Master XLT,
3721221-0D87, PF-40-2N22C, 3721221-1D5ACT, 3721221-0DBMR, and other part numbers were used on this pump.

Motor has wiring diagram showing high, low, and common motor terminals. Green is ground, white is common. High and low colors, red or black are determined by your spa control, not the motor. Fasten the high speed wire to the high speed terminal and similarly, low to low.

A special note on Waterway Model Numbers: model numbers are not as precise as part numbers on the spa pumps by Waterway. Example, pumps labelled PF-30-2N22C can be 12.0 amps or 10.0 amps

PF-30-2N22C can refer to an Executive pump with 3.7 inch intake threads or 3.1 inch.
So..... model PF-30-2N22C can found on at least 4 different pumps. It is recommended you check the amps
rating on your motor, and note the thread sizes on the intake and discharge, and call us to verify if you are
uncertain. 800 584 2717 or, you can always email us a few photos of your old one and we will help:


[email protected]

Accessories for this product...
Pump/Motor mounting pad for 48 frame motors & most 56 frame motors 319-0019, by Waterway Plastics. Motor Base Waterway 3/8" Barbed Drain Plug 413-1201 fits Waterway spa pumps. pack of 1 672-4350 4131201 6724350 Fitting Pump Power Cord for 2 speed pump, electrical power cord 4 wire AMP Plug 46" cord length Pump Wire Harness UNRN20 Repair Nut for Pump Union Coupling 2 inch PVC Pipe Size UNRN20. sold individually. 3.00" ID Threads.
Sale Price: $6.50

Add
Sale Price: $3.90

Add
Sale Price: $18.95

Add
Sale Price: $9.30

Add
Waterway motor mounting pad 319-0019 Barbed Drain Plug for Pump fits Waterway Executive spa pump and other Waterway pumps, 672-4350, 6724350 spa pump power cord AMP connector spa pump repair coupling UNRN20
Pump Union O-Ring pack for pumps with 3 inch threads. Pack of 2 Pump Union Gaskets for 2 inch PVC Pipe Size pumps. 2 Pack, 711-4010
Sale Price: $3.90

Add
Sale Price: $4.50

Add
Pump Union O-Rings for 3 inch threaded spa pumps Pump Union Gaskets for 3 inch threaded spa pumps, 711-4010, 7114010

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

WATERWAY SPA PUMPS > Waterway Executive Pumps > Executive Pumps 3.1" Threads
WATERWAY SPA PUMPS > WATERWAY 2 SPEED PUMPS > Waterway 230V 2-Speed Pumps