Pump replacement 36675 Wavemaster 7000 Watkins, Wavemaster 6000, 06020191-1

Pump replacement for old p/n 36675 Spa Pump for Watkins Hot Spring Spa pumps 115/230V 1-speed 2"SD/CS.

PLEASE SPECIFY IN THE ORDER COMMENTS BOX IF YOU HAVE 1 BIG JET PUMP IN YOUR TUB,

OR, YOU HAVE 2 OR 3 BIG JET PUMPS. IT MAKES A DIFFERENCE IN WHAT MOTOR IS SHIPPED

WITH YOUR ORDER. YOUR ORDER SHOULD NOT SHIP WITHOUT HAVING THIS INFORMATION PLEASE NOTE.

Original pump had changeable voltage, to run on 230 volts or 115 volts.

A replacement for old Hot Spring Spas by Watkins Manufacturing, replacement for Wavemaster 7000, models 36675, 36675-03, Wavemaster 6000, old Power Right pumps, and others, see photo for the style of this version of the 7000, as there is more than 1 style that uses the term 'Wavemaster 7000'. Also is the Sundance/Jacuzzi Theramax II, 06020191-1. Overall length 16-3/8" as shown in the photos. This does not include the length of the Watkins/Hot Springs exhaust vent they sometimes put on these motors years ago. This is also a good replacement for the 06515001-2, HP130, HP-130, Power Right, and 0974101-03 Wavemaster 6500 please note.

Watkins has applied their label to original OEM pumps by Sta-Rite, Vico, Ultrajet, LX Pumps, Power Right, Aqua-Flo, and Balboa over the years, so be sure to look at your style and order the proper style. If you are unsure send us a few photos and we'll help.

Watkins/Hot Springs used "Wavemaster 7000" on at least 6 different pumps, be aware of this. Part number 36675 has been used over the years on several different styles of pump heads from different manufacturers. Look closely at the photos of the style you are choosing before you order and if you have any doubts about which style to order send us a photo of your pump head and we can confirm. "36675" or "Wavemaster 7000" is NOT enough to define you old pump or find the proper
replacement, please note!

Order P120EX21224 if you have 2 jet pumps or more in your tub, each one receiving 230 volts for your control box. 230v In:

Order P115EX22012 if you have a single jet pump in your tub, set to receive 115 volts from the control box. 115v In:

Dual voltage motor rated 20/10 amps, ships from factory set to 230 volts, can be changed to 115 volt operation, see motor label for wire change, and use your original dedicated power cord.

1016171. Replacement for Wavemaster pumps made by Aqua-Flo or by Ultra Jet ®. 17-1/4" overall length. If you have an exhaust hose on the rear of your old motor, use it again on the new motor, it is important to remove the hot air, especially in hot weather.

Replacement for Wavemaster pumps made by Aqua-Flo. Available as Waterway EX2, the replacement for the Aqua-Flo made Wavemasters, see photo. Watkins/Hot Springs uses the term 'Wavemaster 7000' on at least 5 different pumps; be aware of this.

This pump is ideal if you run your motor on 230V. If you run your motor on 115v look at p/n P115EX22012 which is rated 17 amps on 115v and is ideal for 115v applications. P115EX22012
The lower amp draw model P115EX22012 is the better choice if you are cord connected.

IF YOU RUN YOUR PUMP ON 115 VOLTS PLEASE INFORM US. You can leave remarks in the order comments box. And if you run your old pump by putting 230 volts to it, please confirm that for us, Thank you.

The factory ships these set for 230 volts. See motor label for how it should look set for 230v and for 115v.

Order optional union fitting seals here: Gaskets and O-Rings

This pump has one (1) drain plug in place. The other 2 drain plug bosses are not drilled out and tapped, please note. For most applications this is perfect. If you must connect 2 drain hoses to the front using the optional barbed fitting (p/n 672-4350), then you can use a 3/8x3/8x3/8" barbed connector, either a WYE or TEE, from your local plumbing supplier. Most applications that have a drain tube connected to the front of the pump have only 1 tube. 2 or 3 tubes is fairly uncommon